LED防爆灯

性能特点:

Performance characteristics:

运用保护角设计和镜面涂层技术，达到防眩光效果, 能有效减少对作业、施工人员眼睛的刺激，避免产生不适和疲劳感。

Application of the protection angle design and mirror coating technology, reach the antiglare effect, can effectively reduce the operation, construction personnel irritation of the eyes, to avoid discomfort and fatigue.

多重防振结构设计和高强度合金外壳，确保其在路基路轨、桥涵隧道等高频震动中长期安全工作。

Multiple anti vibration structure design and high strength alloy casing, to ensure that the roadbed tracks, bridges and tunnels in high frequency vibration of long term safe operation.

特殊的密封和表面涂层处理, 确保灯具在潮湿、高温等恶劣环境中永不腐蚀, 永不生锈。

Seal and special surface coating, ensure lamps and lanterns never in damp, high temperature and other harsh environment corrosion, never rust.

采用高光效、长寿命的LED光源, 功率因数大于0.85, 光效高，透光性好，寿命长达80000小时。

Using LED light source with high luminous efficiency, long life, power factor greater than 0.85, high light efficiency, good light transmission, long service life of 80000 hours.

座式、吸顶式和壁挂式等多种安装方式，照射角度可根据环境需要在上下180°大范围内调节。

Seat type, absorbing many top and wall hanging type installation, with adjustable irradiation angle degree big scope according to the environment on the 180.

使用范围

Range of use

¤ 适用于爆炸性气体环境的1区、2区场所。

The following is applicable to explosive gas environment zone 1, zone 2 locations.

¤ 适用于ⅡA、ⅡB类爆炸性气体环境。

The following applies to Ⅱ A, Ⅱ B explosive gas environment.

¤ 适用于可燃粉尘环境20区、21区区场所。

The following applies to flammable dust atmosphere 20 District, 21 District places.

¤ 适用于T1-T4（T6)组温度组别

The following applies to T1-T4 (T6) group temperature group

¤ 适用于防护要求较高的环境所使用。

The following applies to require higher environment use.

¤ 适用于石油开采、冶炼、化工、军工储备等企业的危险环境及海洋石油平台，油轮等场所作普通照明及作业照明之用。

The following applies to oil mining, smelting, chemical, military reserve enterprise risk environment and offshore oil platforms, tankers and other places for general lighting and lighting for.

使用方法:

Method of use:

根据现场环境和照明需要，确定灯具的安装位置和方式后将其固定安装；按灯具到

According to the site environment and lighting needs, determine the lamps and the installation position after the fixed installation; according to lighting

220V电源接点的距离，备好相应长度的φ6~8mm电缆线。

220V power supply contact distance, prepare the length of φ 6~8mm cable

用手按压灯头下端两个开盖按钮，掀开灯具前盖，将准备好的电缆线一端通过引入装置的压紧螺母引入灯腔内，按照接线座上标明的极性， 火线接“L”端，零线接“N”端，地线接到接地端，再将引入装置的压紧螺母旋紧。

Hand press holder is two cover open button, open the front cover of the lamp, the cable will be ready by the end of the pressing nut into the device into the lamp cavity, in accordance with the polarity of the marked connection seat, FireWire "L" end, then the zero line "N" end, ground to ground, the compression nut tighten the lead-in device.