• DDPCA-300,德国FEMTO可变增益电流放大器


     品牌:FEMTO  型号:DDPCA-300  加工定制:否  
    *大峰值噪声0.4 fA
    9级可变增益:104~1011 V/A
    240 dB Dynamic Range for Sub-fA to mA Measurements
    Adjustable Voltage on Input for DUT Biasing
    Compact Housing for Use Close to the Signal Source
    Manual and Remote Control
    Sub Femto Ampere Sensitivity

    The variable gain sub femto ampere amplifier DDPCA-300 is the latest addition to FEMTO's broad range of low noise transimpedance amplifiers. Its exceptional design achieves input noise values down to 0.2 fA/√Hz and 0.4 fA peak-peak. The gain can be set over a very wide range from 104 up to 1013 V/A either manually or by a remote interface. Thus, the amplifier covers a large dynamic range of more than 240 dB for the measurement of currents from sub femto amps up to milli amps by simply switching the gain range. The compact housing is optimized for use close to the signal source avoiding signal perturbations or noise pick-up due to long cables. Various filters are integrated to adapt the amplifier bandwidth to varying signal conditions. Thus, the signal to noise ratio and measurement speed can be optimized by selecting the proper filter setting for a specific application. And even in the highest gain settings the measurement speed is sufficient to measure femto amp currents in real-time without the need for external averaging or long test periods (see figure 1 below).

    Low Drift for Stable Long-Term Performance

    At the femto ampere level drift and offset currents can easily cause measurement errors and shifting baselines. The design of the DDPCA-300 is optimized for long-term stability and extremely low drift. The below figure shows the amplifier's baseline drift of less than 0.5 fA measured over a period of more than 7 hours. In case of inevitable (e.g. temperature related) offsets an trimpot is provided for cancelling unwanted offset currents and for nulling of the baseline.

    Device Characterization by Source Biasing

    The very high sensitivity of the DDPCA-300 can be utilized in low current applications like characterization of high resistance semiconductors (e.g. MOS or JFETs) or quantum-dot devices. An adjustable voltage is supplied directly at the amplifier input for biasing the device under test (DUT). Changing the bias voltage manually or through the remote interface in the range of +/- 10 V allows the characterization of the DUT for different bias voltages in spectroscopic measurements. For applications not requiring a bias voltage like photocurrent measurements or beam monitoring in particle physics the bias voltage can be easily disabled.

    • Photo and Ionization Detector Amplifier
    • I/V Characterization of MOS and JFET Structures
    • DC Measurement of Ultra Low Currents

    • Quantum and Biotech Experiments
    • Spectroscopy
    • High Resistance Measurements
    • Easy to Use Femto Amp Add-on to Existing Digital Voltmeter or A/D Converter

    Transimpedance [V/A] 104 105 106 107 108 109 1010 1011 1012 1013
    Bandwidth* (- 3 dB) [Hz] 400 400 400 400 150 150 20 20 1 1
    Rise Time* (10% - 90%) [ms] 0.8 0.8 0.8 0.8 2.3 2.3 17 17 350 350
    Integrated Input Noise* (Peak-Peak) 7 nA 7 nA 70 pA 70 pA 1.2 pA 1.2 pA 50 fA 50 fA 2 fA 2 fA
    Spectral Input Noise Density [/√Hz] 45 pA 45 pA 0.5 pA 0.5 pA 15 fA 15 fA 1.3 fA 1.3 fA 0.2 fA 0.2 fA
    Accuracy Performance Gain ± 1 %
    Adjustable Low Pass Filter 3 Settings: Full Bandwidth, 0.7 Hz and 0.1 Hz
    Output Performance ± 10 V, ± 30 mA
    Bias Voltage ± 10 V, max. 10 mA, Connected to Amplifier Input, Adjustable by Trimpot or Remote Control Voltage
    Power Supply ± 15 V, + 70 mA / - 15 mA typ., ± 150 mA recommended
    Control Interface 4 Opto-Isolated Digital Inputs, TTL/CMOS Compatible, Analog Bias Control Voltage Input
    Case 170 x 60 x 45 mm (L x W x H), Weight 320 g (0.74 lb.)
  • 留言

    联系人: *(必填)
    手    机: *(必填)
    电    话:
    公    司: *(必填)
    地    址:
深圳市博纳德精密仪器有限公司 地址: 深圳市宝安区45区鸿都商务大厦A栋301室 技术支持:谷瀑环保 免责申明 管理员入口